Century-systems CFD-4306 Manual do Utilizador

P/N. MD4206U-01 Edition 1 June 2004 Century Falcon 4D User Manual Table of Contents

7 2-3 Label Roll Core Installation Instruction (A) 1” roll core installation instruction (B) 1.5” roll core installation instruction

8 2-4 Card / Hang tags Installation When installing cord tags, the tag hole must align with the sensor arrow (as indicated in Photo 1), then use th

9 2. Select ” Search for a suitable driver for my device [recommended]“ and click “Next” 3. Select the location of the driver. 4. When the USB

10 5. The USB device is built on the serial port, therefore make sure the interface setting is specified to the assigned port. 6. Go to Contr

11 2-7. PC Connection 1. Please make sure the printer is powered off. 2. Take the power cable, plug the cable switch to the power socket, and the

12 Chapter 3 - Options Installation 3-1. Stripper Parts 27 Stripper Module 28 Screw (TAP 3*8) x 2pcs [NOTE]: Please power off the printer befo

13 6. Place the right side in first, and then fit the left side. 7. Hold the stripper module and tighten the screws (28). 8. Peel off the

14 3-3. Stripper Installation Diagram Stripper Installation Diagram LA

15 3-4. Cutter Parts 29 Cutter Module 30 Screw (TAP 3*8) x 2pcs [NOTE]: Please power off the printer before installing the cutter module. [NO

16 4. Open the mechanism by pressing the Locking Tenon, plug in the cable connector of the cutter module (29) onto the switchboard socket. Note: T

i FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursua

17 7. Hold the cutter module and lock it with the two side screws (30). 8. After the screws are locked, flip close the cutter module. 9

18 3-7. Extended Memory Installation 1. Open the top cover by pressing the Cover Open Buttons on both sides. 2. Take off the media roll spindle.

19 3-8. Ethernet Parts 33 Ethernet Module 34 Connector Cable 35 Network Board Stand 36 Screws (MACHINE 3x6) x 2 37 Scre

20 4. Secure Ethernet Module (33) and Network Board Stand (35) together as shown in Figure 2 。 (Figure 2) 5. Screw the sec

21 Chapter 4 - LED Message Description 4-1. LED Status FEED LED Ling Beep Status Description READY Green STATUS 1 Normal status Normal status

22 CFD-4206: V1.200 Serial port: 96,N, 8,1 1 DRAM installed Image buffer size: 1472K 000 FORM (S) IN MEMORY 000 GRAPHIC (S) IN MEMORY 000 FONT

23 4-4. Dump Mode When label setting and the print result don’t match, it’s recommended to go into the Dump Mode to check whether there’s a mistake

24 4-7. Error Messages LED Light LED Message Ready Status Beep Description Solution Print head is opened Red 4 beeps twice Print head not firmly

25 Chapter 5 - Maintenance and Adjustment 5-1. Thermal Print Head Cleaning Unclear printouts (some parts unable to print) may be caused by dusty prin

26 5-3. Print Line Adjustment Use print head adjusting gear to adjust the contacting surface between print head and label. To get better printing ba

ii WARRANTY INFORMATION ...II CHAPTER 1 – BARCODE PRINTER ...

27 5-5. Troubleshooting Problem Recommended Solution Power on the printer, but the LED does not light up  Check the power connector LED light tur

1 Chapter 1 - Barcode Printer 1-1. Introduction The Century Systems FALCON 4D series is a desktop thermal transfer / direct thermal label printer.

2 1-4. General Specifications Model Name CFD-4206 CFD-4306 Resolution 203 dpi (8 dot/mm) 300 dpi (12 dot/mm) Print Mode Thermal Transfer / Direct

3 1-5. Communication Interface Parallel Interface Interface cable : Parallel cable compatible with IBM PC Pin out : See below PIN NO. FUNCTION

4 1-6. Printer Parts Please use the following diagrams to identify each printer part. 1 Cover Open Button 11 LED Light (Ready) 21 P

5 Chapter 2 - Printer Installation This printer model has the following print modes: Thermal Transfer (TT): When printing, ribbon must be installe

6 2-2. Label Installation 1. Open the top cover. 2. Place the label roll onto the Label Roll Core, 3. Loosen and lift the upper print m